Category Archives: Cars

1935 Bugatti Type 57S Compétition Coupé Aerolithe

What a treat today has been! Drove to the High Museum of Art Atlanta to see the Dream Cars collection exhibition, which will continue until September 7, 2014. If you get a chance to make the drive, I highly recommend it. A total of seventeen concept cars are on display each magnificent except for two turds. Both German – one, a BMW and the second a Porsche. Oh well, can’t have it all I suppose.

So I’ll start by listing what I thought was the most impressive in the collection: a 1935 Type 57S Compétition Coupé Aerolithe. The finish of this car is a shade of very light green metallic that exhibits properties akin to a chameleon: one moment it looked light green, and the next it became almost silver. And yes, this is the Bugatti with the exposed backbone assembled with hundreds of rivets. Feast your eyes…

The front of the car displays an immense amount of exceptionally perfect chrome. The grill has what appears to be thermostatically controlled vertical blade arrangement allowing the correct amount of cool air to keep the engine from overheating. The headlights were particularly impressive: everything was crystal-clear except for the bulbs: they were yellow. The side vents on the hood were also flawless and the latches holding the sides were magnificent.

Moving right along, notice the doors. What a door! Check out how high the door sills are and the teardrop design of the side glass window. The occupant’s shoulder would be even with the lower edge of the window – how awesome is that? Finally as if it were not obvious enough, those are suicide doors held in place by two delicately made door hinges. To make something look this simple and elegant takes an obscene amount of knowledge, craftsmanship and time.

Here is a closeup of the rear wheel cover. The cover has five fasteners that when turned in the correct direction allow the cover to be removed. Pay close attention to the lower right corner where the wheel cover meets the rear curve of the fender. The amount of detail is immense. The cover has a compound curve – it boggles the mind how this the master craftsman in charge hand-formed this from a sheet of metal using his hands, an English Wheel, perhaps a planishing hammer… And it goes without saying, but look at all those rivets holding the fender to the rest of the body.

The tail of this Bugatti is once again an amazing work of art. Here we see the exposed backbone with all those alternating rivets. The spare wheel must be under that large round cover. Notice how perfect the sweeping seam on the fender meets the backbone in the middle. Finally, below the roll-pan are four very tastefully placed indicators. They are just neatly tucked away as to not distract the eye from the flowing curve of the back of this work of art. Amazing don’t you think?

Here you see the four lights I mentioned before, but wait… Look at that simple but elegant chromed release handle for the boot cover. It appears to be designed to be lifted and then pulled back where it would rest on a detent. Then the entire back cover would open.

This picture shows the exposed backbone actually goes under the car for a certain distance. I was unable to get a closer look but I think there are even more surprises under all the shiny bodywork. If you look close enough towards the left, you see that small tapered point on the wheel cover that shows just how high the level of detail exists on this coachwork.

Here are the back windows. Unfortunately the light was not good enough to show the interior, but from this vantage point I could actually see all the instrumentation as well as the dash and steering wheel.

I realize this is not exactly the best of photos, but look at how the door extends into the roof area of the car. I suppose this would have aided the occupant when entering/exiting the inside of the car. Nothing seems left to chance here. Exceptional, don’t you think?

I took the two pictures above, to highlight something particular about this car. The entire body is a flow of curves. The long swooping fenders, the compound curve of the rear wheel cover, the roof, the curves on the rear deck… Except for one thing… Look at the extreme sharp edge on the engine cover as it meets the firewall. Then think when this was all formed: the mid 1930’s. This is not a car – this is art.

Finally, I’ll just close with a few more pictures of this exceptional rolling masterpiece.

Stay tuned… I took many pictures of the rest of the cars in the collection. I’ll try to write about them in the next few posts

The Chevrolet Cameo Pickup

Leave a reply

Back in the mid 1950’s, the Chevrolet Cameo pickup was the first of the high-end luxury trucks with real pizzazz. Thanks to the knowledge General Motors obtained from the plastic-fantastic Corvette, the Cameo’s outer bed panels were made of lightweight fiberglass. At the time the Cameo came equipped with a high-end interior, the best of V8 power, automatic transmission and two-tone paint. In the 1950’s this made the Cameo a very avant-garde vehicle, and thus not many were built. Even more obscure is the GMC version – the Suburban Carrier.

Today, the Cameo is very rare. Today, I had the privilege to work on one (again!) – oh lucky me!!

In a none-too-distant-future this Cameo will be a stablemate to my friend Barry’s Bel Air (click here to see it). What makes this Bel Air so damn special is that it has been in Barry’s family since new. Just imagine still owning the car you grew up since you were a kid!!

This Chevrolet Cameo has been at my cousin Jim’s shop numerous times on its way to being brought back to life. Jim has modified the frame, installed the new LS 5.3 liter engine (oh hell yeah!!) and done a huge amount of other fabrication work. I have written about it before; you can read more about it by clicking here and here.

Today we did some bodywork on the fiberglass outer bed panels.

Body filler applied to the “low spots”.

To get the bed panels nice and straight, my cousin Jim previously sprayed them with sanding primer (the gray stuff) and today we worked some body-filler in order to ensure a very straight finish. Body filler is applied to the “low spots” on the panels. The great majority of this will eventually be sanded down. This takes patience and a steady hand. Yes it is tedious, it is messy (you get a ton of powder all over the place) and it takes time. And time. And more time. And yes, you guessed it, more time.

I’ve had quite a bit of stress and aggravation in the last few weeks, so working on Barry’s truck today was very therapeutic. This is the kind of stuff that “builds character”. It gives you time to think and well… I just enjoy doing this!

Sanding was done using an orbital air-powered sander, several sanding blocks of different shapes and sizes and different grades of sand-paper. Of course this is July 4th weekend and it was nice and warm (no – it was HOT!). Fortunately we had a few box-fans running and this made it tolerable.

Some folks say this is boring and a pain in the ass. Nope. This brought back fond memories of the endless hours I spent the summer I did this very same work on bowtie6 (click here). What made the Cameo different was that the sanding had to be more careful because I did not want to dig into the fiberglass gel-coat. After several hours we had this:

The end result, after a few hour’s worth of sanding.

What is left now is just a film of filler covering the “low” spots on the body panel. If you look closely you can see some of the sanding blocks (on the top of the bed and on the floor). We had air-powered versions too but this has to be done the old-fashioned way: by hand.

Here is the cab on Barry’s cameo (yes, the photo is not perfect, I used my iPhone!):

The Cameo’s cabin.

The opposite side, after sanding was completed.

So what’s next?

Well… We have some more sanding to do. There were a few spots that needed some more filling and further sanding to get really, really smooth. Then another coat or two of sanding primer followed by more sanding with even finer sandpaper. The idea is to get the surface straight and smooth.

Man! This was fun today. If you have never done this kind of work before, you are missing out on one of the pure joys of auto-restoration. I highly recommend it!

How is it done?

Filler is mixed from a paste in a can. Usually you would get about a golf-ball sized amount and add a pea sized amount of catalyst. This is then mixed very quickly on a special pad lined with paper until thoroughly blended. Then the fun begins. You must spread this with a special pad thin enough and quick enough while it is still malleable. After just a few minutes there is a point-of-no-return when the stuff gets too hard and grainy. On a hot day like today, the set time is even shorter.

Then, the filler is allowed to fully harden. Once it is hard to the touch, one can start sanding. The end result is a very fine powder that goes everywhere. Yes, it has a special odour and when I say it goes everywhere I really mean it. However, there is nothing like the feeling of accomplishment when you take an air-hose and then gently rub your hand on the body panel. If you have done it right, it will be as smooth as a newborn’s arse.

I’ll have more updates soon…

MTM Hydro Professional Foam Lance Review

2 Replies

From what I’ve read on the auto detailing forums, the MTM Hydro Professional Foam Lance is the only way to properly wash a car. This device is attached to your pressure washer and with the right kind of soap, a perfect layer of foam can be delivered to the surface of your car.

I did some research on the inter-webs and found there are several vendors. Since I am not endorsing one or the other, I picked the one with the lowest price (and yes, they vary!) so if you decide to get one do your homework. Sure enough, a few days after I placed my order the friendly UPS driver delivered a package with an MTM Hydro Professional Foam Lance and on Memorial Day weekend I decided to try it out. Here is what I found…

What You Get in the Box

So what do you get in the box after in return for your hard-earned $79 bucks? As you can see from the featured image, the box is nicely labeled and the contents are: a lance assembly, two fittings, a clear plastic tube and the plastic bottle used to hold an auto soap mixture. The clear plastic tube siphons soap mixture from the plastic bottle.

The lance is quite heavy and appears well made. This picture shows the lance with the clear plastic siphon tube attached on the bottom; on the right is the fitting that matches my pressure washer. The top knob regulates the amount of soap mixture being sucked in and the black lance on the left works just like the tip of a pressure washer: it regulated the sweep area (from a fan to a concentrated point) by turning one way or the other.

The bottle looks like this.

The Pressure Washer

I have a Sears gas-powered pressure washer, like this one:

From what I have read on the forums, finding the “right” fitting to match your trigger is a bit confusing. Fortunately in my case, the correct fitting came in the box. Here is what the MTM Hydro looks like with the proper fitting for my pressure washer:

This part was rather frustrating for me. I tried several times to contact one of the vendors about the fittings and after several tries finally received a rather vague answer on whether the MTM Hydro lance would fit the Search trigger mechanism. However all worked out right out of the box.

Using the MTM Hydro Professional Foam Lance

Once I got everything assembled and had the pressure washer up and running, let me just say this thing works very well. Since I am doing a full report here for you, I will explain the good and the bad.

First, let me tell you the bad: the Achilles heel of this whole affair is the bottle. It is very cheap and flimsy. During transit the box appears to have been bumped a bit and the bottle showed signs of being semi-crushed. Look at this picture:

I tried to straighten out the crease a little, but this bottle is made of such thin material that I am afraid to mess with it too much in fear it will just out rip. Another issue I find in the bottle is that when it is full of soap mix, it is extremely easy to cross-thread on the lace. This is what the threads on the bottle look like:

And they thread into this:

However, if you take your time then you can get the bottle properly screwed in. Bottom line, I see myself having to buy a replacement bottle sometime in the near future. So it might not be a bad idea to get an “extra” bottle with your order.

Next the good: this thing works. But… Be aware the amount of foam will depend to a large extent on the quality of car-wash soap you use. My first attempt was using Griot’s Garage car-wash:

And this is what it looks like after a minute or two after applying:

This soap gave good results. I had two other bottles of car-wash I had previously bought at the local Auto Zone and those failed miserably producing almost no foam at all. I realize there are probably better car-wash shampoo options out there, I’ll just have to find them. When I do, I’ll have an update.

Oh and one more thing: Keep an eye on the bottle as its contents get used up… 😉 In my case, the pressure washer had enough suction that it started to crush the bottle like an empty beer can. Just watch the soap mixture!

In Conclusion

The foam lance worked very well. It produced a very nice layer of foam and overall I was very pleased with how my S2000 and later, bowtie6 looked after all the foam was rinsed away. Was it worth having to break out the pressure washer and all its attachments? I guess I’ll have to try this out a few more times before I can say for certain.

1967 Honda RA300 F1 Car

Vintage Alfa Romeo F1 Race Car